Edofnor
Veteran XX
in 2020 people use tools
ftfy
Roof technology
- Thread starter Plasmatic
- Start date
ftfy
StapleMammal1
Contributor
For example. See what she is doing? Peeling off the shingles? Had she started at bottom corner, and worked her way up, she would not need that tool to remove the shingles.
Pull and peel with the right pressure and you can basically get off a whole square at a time.
(a square is 10'x10' if memory serves me correct.)
Pull and peel with the right pressure and you can basically get off a whole square at a time.
(a square is 10'x10' if memory serves me correct.)
Last edited:
StapleMammal1
Contributor
same, but skinny chicks always bitch it's too deep. you want a chick with thick ankles. they usually can take it deep no prob. that fat bitch that broke my futon sure as fuck did. 
Last edited:
Correct.
I used these. Had the roof and some of the wood off in a day.
Yes, it came off in big chunks. The singles were ok, but the install and wood wasn't.
Flashing under shingles, vents installed upside down, barely any ice shield, rotten wood, etc.
Sent from my SM-G973U using Tapatalk
Yes, it came off in big chunks. The singles were ok, but the install and wood wasn't.
Flashing under shingles, vents installed upside down, barely any ice shield, rotten wood, etc.
Sent from my SM-G973U using Tapatalk
Took yesterday off, pictures from this morning before the snow and Saturday
Pulled up this stupid piece of crooked wood
Surprise, not a square corner on it. Managed to slip in the bitch clips.
Nothing on this sun room is square or straight. Here's a nice gap near the valley by the ladder. Where the first sheet was rotten.
From there I pulled the sheet off the corner. Had some rot under the drip edge.
Found some surprise gold
Thankfully they were pretty slow from the cold and I managed to hose them all down before they got too frisky.
Check out how high the rafter under my boot is compared to the others around it. They're obviously getting in there between the sheet and face board. I'm not going to rebuild this whole goddamn sun room so I'll cram some gutter apron in there when I can.
Cleaned up and swept out all the carcasses.
Dropped a sheet on there, managed to keep it on the roof without it taking me with it.
Surprise the goddamn corner isn't straight. Sawed off a wedge nearly an inch wide from the bottom up towards the peak.
From there I ran ice shield and paper up under the existing paper near the top and started shingling. Got this done before dark.
Cleaned up and flopped the tarps back down.
Rained yesterday and this morning. Went up and took these pictures before the snow.
Pulled up this stupid piece of crooked wood
Surprise, not a square corner on it. Managed to slip in the bitch clips.
Nothing on this sun room is square or straight. Here's a nice gap near the valley by the ladder. Where the first sheet was rotten.
From there I pulled the sheet off the corner. Had some rot under the drip edge.
Found some surprise gold
Thankfully they were pretty slow from the cold and I managed to hose them all down before they got too frisky.
Check out how high the rafter under my boot is compared to the others around it. They're obviously getting in there between the sheet and face board. I'm not going to rebuild this whole goddamn sun room so I'll cram some gutter apron in there when I can.
Cleaned up and swept out all the carcasses.
Dropped a sheet on there, managed to keep it on the roof without it taking me with it.
Surprise the goddamn corner isn't straight. Sawed off a wedge nearly an inch wide from the bottom up towards the peak.
From there I ran ice shield and paper up under the existing paper near the top and started shingling. Got this done before dark.
Cleaned up and flopped the tarps back down.
Rained yesterday and this morning. Went up and took these pictures before the snow.
Last edited:
My roof technology is advancing.
Fml
Sent from my SM-G973U using Tapatalk
you've been working on this for a month
KingSobieski
Veteran XX
Have you considered hiring some $20/hr Craigslist roofing guy to help out?
Sent from my Moto Z (2) using Tapatalk
Sent from my Moto Z (2) using Tapatalk
Supposed to be in the high 50's/ low 60's tomorrow. I'll run Ice shield and drip edge where the tarp is over the garage (by the ladder) and see where I end up. Hopefully dry enough by then to finish shingles on the sun room and start shingles over the garage.
Is this Mason code for something?
Todays progress. Built a triangle
Chalk line up the last valley
Really digging the valley technique. Makes for a crisp edge.
Then it started to rain. Heavy for a few minutes
Turned onto a mist, ended up 8 shingles short.
Covered it up with a small tarp and some paper.
Shout out to my cutting board. Maybe I'll frame it.
Storming out now. Picked up another bundle earlier tonight. I'll finish shingles tomorrow after the rain, and do the stupid stink pipe flash and ridges.
Chalk line up the last valley
Really digging the valley technique. Makes for a crisp edge.
Then it started to rain. Heavy for a few minutes
Turned onto a mist, ended up 8 shingles short.
Covered it up with a small tarp and some paper.
Shout out to my cutting board. Maybe I'll frame it.
Storming out now. Picked up another bundle earlier tonight. I'll finish shingles tomorrow after the rain, and do the stupid stink pipe flash and ridges.